Expert Answers about Hitch Aligners
- Can the Battery On the Swift Hitch Wireless Hitch Alignment Camera Be Replaced
- Yes, you can replace just the battery on a Swift Hitch Wireless Hitch Alignment Camera. The correct replacement for you will be dependent on what what system you have. If the system you have uses a 4 hour battery then you need the Replacement Battery for Swift Hitch SH01 Camera part # PB02 but if the system you have uses an 8 hour battery then you need the Replacement Battery for Swift Hitch SH02 and SH03 Camera part # PB06.
view full answer... - Can I Get a Replacement Camera for the Hopkins Smart Hitch Backup Camera and Hitch Aligner System
- To replace the camera on your Hopkins Smart Hitch Backup Camera and Hitch Aligner System # HM50002 you will unfortunately have to get the whole kit again as Hopkins doesn't offer the camera only as a standalone replacement part. The good news is that the wiring should be plug-and-play and you'll have a spare monitor, but the bad news is that it's not as cost-effective as it should be.
We do have other backup camera solutions available (see linked selection) but most of them are at a higher...
view full answer... - Replacement Batteries for Swift Hitch Wireless Hitch Alignment Camera
- Our part number for the Swift Hitch SH01 is # 04928. The # PB01 is the correct replacement battery for your monitor. The replacement battery for the camera is # PB02.
view full answer... - What Replacement Hitch Pin Do I Need for My Kuat Transfer V2 for a 1-1/4" Hitch?
- For a replacement hitch pin for your Kuat Transfer V2 for a 1-1/4" hitch, you will need the Hitch Lock for Kuat Bike Racks - 1-1/4" Hitches # HL1. This particular pin has a diameter of 3/8 on an inch and an overall length of 5-3/4 inches.
view full answer... - Is There a Replacement Camera for the Hopkins Smart Hitch or a Replacement System
- The Hopkins Smart Hitch Backup Camera and Hitch Aligner System part # HM50002 is an all in one unit. There is not a seperate back up camera only part that can be added.
If you are going to replace the system the Rear View Safety Wireless Backup Camera System part # RVS-091406 is a better option for the replacement as it is designed by a company that specifically works with camera systems. The camera and view are of higher quality and one I definitely recommend.
view full answer... - Are The Square Hole Spacers Required on Draw-Tite Trailer Hitch Receiver # 75270 & Where To Get More
- The spacers used on the Draw-Tite Max-Frame Trailer Hitch Receiver # 75270 are used to space the receiver off of the frame enough so it does not hit the parts of the frame which do not fit flush with the frame where the bolts align. The only way we offer these particular spacers is in the Replacement Hardware Kit # RHK. Per Draw-Tite they are required for the installation.
view full answer... - Replacement Parts for Weight Distribution System Needing Adjustability
- We don't carry any hitch head compatible with the EAZ Lift bars. My recommendation is to replace the weight distribution system with the Fastway e2 Weight Distribution w/ 2-Point Sway Control - Round - 8,000 lbs GTW, 800 lbs TW # FA94-00-0800. This is rated for total tongue weights between 400 and 800 lbs. You will also need the hitch ball # 19286.
This replaces the entire system so it is new shank, head, bars, and brackets. The benefit is they are designed to work together correctly.
view full answer... - Solution for Replacement Parts for Older Sterling Tow Bar
- It sounds like you were looking for a replacement sting shank for your older Roadmaster tow bar. I reached out to Roadmaster and found that replacement parts are no longer available for this tow bar since it has been discontinued for some time. The only solution is to replace the tow bar with a new one.
For a replacement I recommend the Roadmaster Falcon All Terrain, Non-Binding Tow Bar # RM-522. This tow bar has a non-binding design and is self-aligning. It features extra-long telescoping...
view full answer... - Replacement Brake Actuating Coupler for Upgrade to Disc Brakes
- The bolt hole dimensions of the Demco Brake Actuator # DM8669112 are 12-1/2 inches on center and 3 inches on center. I've attached a photo to assist.
The Titan # T4747220 has mounting holes that are 3 inch on center so 2 of the 3 holes will align with your current coupler.
Instead of changing out your entire coupler, you may want to simply change out your master cylinder on your Demco Actuator using the Replacement Master Cylinder for Demco Actuators - Disc Brakes # 5672. This will...
view full answer... - Replacement Landing Gear Motor for 1-065-041012
- The correct replacement motor would be the Lippert # LC141893 which is also a 7140 rpm motor. If you want to swap out the gearbox as well, use part # LG-179015.
I'd also suggest trying to manually operate the legs to make sure they're not bound up.
Keep in mind, the motor and landing gear only need to lift the pin weight of the trailer, not the entire weight. Much of the weight will be supported on the trailer's back axle(s). The motor's 5000 lb capacity is more than enough to handle...
view full answer... - Replacement 3 Inch Goosneck Ball for Unknown Gooseneck Hitch on 2008 Ford F-350 Long Bed
- Gooseneck hitches typically use a 2-5/16 inch ball, but occasionally you'll see a 3 inch. Without knowing the manufacturer and model or part number of your gooseneck hitch, I wouldn't be able to speculate on a replacement ball. You can look at the underside of the hitch and see if there are any part numbers or manufacturer info, and reply with any info you can find and I'd be happy to see if anything we offer would be compatible.
Lacking that information, my best recommendation for you...
view full answer...
Go To Results